Color Depth Test

Inspect gradient banding, near-color separation, and possible dithering artifacts with three browser-based visual test modes. The patterns are references for comparison, not a direct measurement of your panel's native bit depth.

Gradient banding Near-color pairs Possible FRC clues Fullscreen check
← Harder (dark · low value diff) Easier (bright · high value diff) →

No obvious flicker in this check · Flicker or grain may indicate a visual artifact

Click to Enter Fullscreen Test

Compare gradient steps, near-color pairs, and grey patches.

Color Depth Test Dark Gradient
Look for steps in the darkest part of each bar
Color Depth Test Visual comparison · Select a mode
Dark Gradient Visual comparison

Test Mode

Assessment Guide

Smooth GradientNo banding · Good dark distinction → 8/10bit
Visible BandingDark steps or merged tones · Review the pipeline and panel specifications

System Info Reported

Browser Output Signal24-bit
Native Panel DepthNot measured
HDR Media Signal—
Reported Color Count16.7 million

Depth Comparison

6-bit Entry 262K colors64 levels/channel
8-bit Mainstream 16.7M colors256 levels/channel
10-bit Pro 1.07B colors1024 levels/channel

What This Color Depth Test Can Show

This color depth test provides three visual comparisons for common 6-bit, 8-bit, and 10-bit workflow questions. Use it to inspect visible transitions and possible artifacts, then confirm the panel specification and output path separately.

Gradient Banding Check

Dark and full-range gradients make visible steps easier to compare. Banding can be related to output depth, but it can also come from the source image, gamma, color management, compression, or the panel itself.

Near-Color Comparison

Adjacent patches use small RGB differences so you can compare which transitions remain visible. Viewing conditions, scaling, browser rendering, and the display's processing can all affect what you see.

Possible Dithering Clues

Static grey and color patches can help you notice possible flicker, grain, or temporal changes. A visual impression alone cannot identify FRC or prove native panel depth.

What Does Color Depth Mean?

Color depth describes how many discrete levels are available for each color channel. More levels can make smooth gradients easier to represent, but the final image also depends on the complete display pipeline.

6-bit

Six bits per channel provide 64 levels for red, green, and blue, or about 262,000 direct RGB combinations. Some displays use dithering to represent additional intermediate tones.

8-bit

Eight bits per channel provide 256 levels and about 16.7 million direct RGB combinations. This is a common output target for everyday desktop, web, and video workflows.

10-bit

Ten bits per channel provide 1,024 levels and roughly 1.07 billion direct RGB combinations. Whether that extra precision reaches the panel depends on the GPU, connection, application, settings, and display hardware.

How to Use This Color Depth Test

Use the patterns as a repeatable visual check, then compare what you see with the display's documentation.

  1. Start with the dark gradients Look for abrupt steps, merged tones, or changes that stay visible across the bars. Do not treat one visible band as proof of a specific panel depth.
  2. Compare the near-color pairs Move from the darker pairs toward the brighter ones and note where the two patches become difficult to separate. Keep browser zoom and display scaling at their normal values.
  3. Check the dither patches Watch the grey and dark color patches for a few seconds. Note any obvious flicker or grain as a possible artifact, then use the monitor model and manufacturer specifications for confirmation.

Color Depth and FRC Terminology

These terms help explain why an advertised color count and a visual test result may not tell the whole story.

FRC (Frame Rate Control)

FRC is a dithering method that can alternate nearby tones over time to represent intermediate values. It is often discussed alongside 6-bit+FRC and 8-bit+FRC specifications.

Spatial Dithering

Spatial dithering distributes nearby colors across pixels rather than relying only on frame changes. A browser pattern may make some texture or grain visible, but it cannot identify the processing method with certainty.

Native vs Reported Depth

A specification may describe panel hardware, while the operating system and browser expose an output or rendering value. Compare both with the same test conditions instead of assuming the values are interchangeable.

HDR & Color Depth

HDR workflows often use higher precision to reduce visible steps across a wider brightness range. HDR support alone does not prove native 10-bit panel hardware, and banding can have several causes.

Why Color Depth Results Can Differ

A visual pattern reflects the whole signal path, not only the panel specification. These common situations can change what appears on screen.

Panel Specification

Check the source:

  • Use the exact model number from the display or its OSD menu.
  • Check the manufacturer's technical specification rather than only the color-count headline.
  • Look for separate entries for native depth, maximum input depth, and FRC.

8-bit + FRC

Why it matters:

  • Dithering can represent additional intermediate tones beyond the direct channel levels.
  • Static patterns may look smooth even when the implementation is not native 10-bit.
  • Possible flicker or grain is only a visual clue, not a conclusive identification.

Output Pipeline

Check the connection:

  • GPU settings, refresh rate, resolution, cable bandwidth, and application support can affect output.
  • A higher setting in one application does not guarantee the same path everywhere.
  • Repeat the comparison at the display's native resolution and normal scaling.

Viewing Conditions

Control the comparison:

  • Use a stable viewing angle and moderate ambient light.
  • Browser zoom, operating-system scaling, and display processing can change small differences.
  • Compare a suspected issue more than once before drawing a conclusion.

Color Depth Testing and Output Tips

Use these checks to make the visual comparison more repeatable before changing display settings.

Check the output setting

Review the GPU or operating-system output-depth setting, but treat it as a pipeline value rather than proof of the physical panel depth.

Use native resolution

Run the patterns at the display's native resolution and normal scaling so the browser is not introducing an avoidable resampling step.

Review the connection

Resolution, refresh rate, cable standard, and GPU output limits can change the signal that reaches the display. Check them together.

Compare inside the real workflow

If banding matters for video, games, or design work, compare the browser result with the application and source material you actually use.

Frequently Asked Questions

Common questions about 6-bit, 8-bit, 10-bit output, FRC, and browser-based visual checks.

What can this color depth test tell me?

It can help you compare gradient steps, nearby color patches, and possible flicker or grain. It cannot identify the exact physical panel implementation by itself.

Can an online test confirm native 10-bit?

No. Browser patterns are useful visual references, while the display model, manufacturer documentation, OSD, GPU settings, and connection determine the rest of the answer.

Why might I see banding on an 8-bit or 10-bit setup?

The source gradient, application, color management, gamma, compression, output settings, or panel processing can all create visible steps. Bit depth is only one part of the signal path.

What is 8-bit+FRC?

It is a display approach that uses dithering to represent additional intermediate tones. The exact behavior varies by panel and processing, so a visible pattern cannot prove whether FRC is being used.

What does “32-bit color” mean in system settings?

That label often refers to a software color format with 8 bits per red, green, and blue channel plus an alpha channel. It is not the same as proving the panel's native hardware depth.

How do I verify the result?

Repeat the visual check under stable conditions, then compare the display model's specification with its OSD and GPU output settings. Use the browser result as supporting evidence, not as a final hardware diagnosis.

Before You Judge a Color Depth Result

  • Control the room: Use stable ambient light and sit at a normal viewing distance.
  • Keep the pipeline stable: Avoid changing resolution, refresh rate, scaling, or picture modes halfway through the comparison.
  • Repeat the observation: Check a suspected band or flicker more than once before treating it as a display issue.
  • Confirm with specifications: Use the exact model documentation to distinguish native depth, maximum input depth, and FRC claims.

More Color Testing Tools

Pair the color depth test with related visual checks for color, gamut, and grayscale behavior.

Inspect Your Display's Color Depth

Compare gradient steps, near-color patches, and possible dithering artifacts in your browser. Use the result alongside your display specifications and output settings.

Browse More Tools